Outdoor Living Today SR812 Instrukcja Użytkowania i Eksploatacji

8x12 Santa Rosa Assembly ManualSome of the safety and usage measures you may wish to consider include:-snow load ratings vary by geographical location

20. To complete walls, attach the Narrow Porch Wall to front wall panel. Note: the narrow wall isonly 73” high. Attach wall stud to adjoining wall w

22. When all walls are attached together,check alignment with the floor. Bottom wallplates should sit flush with outside of floorframe. When positione

25. Position the FrontTop Plates on top of DoorHeader and front wallpanel. There are 2 plates(72” and 19” long). Fronttop plates are straight cuton t

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected] 13Top Plate Front ExtensionA.B.C.Handrailequallyspac

28. When both porch sections are completed, lift Right Side Section into place on deck beneath theside top plate. Attach Wall Trim/ Support to wall w

32. Align Top Door and space as per Bottom Door on sides. Leave a 1/4” gap between the Bottomand Top Door. When in correct position, secure hinges to

37. Position the Rear Gable Wall on top ofthe Rear Top Plate. The rear gable framingshould sit flush with the inside of the top plate.It should also

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected] 17OutsideRoofPanels (2)Middle RoofPanels (2)Exploded

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected] 1843. Attach end of a 68 1/4” long Soffit Bo

44. Carefully lift 1 completed Rafter Section up (make sure Soffit is facing down) and place on gableframing.46. To confirm Rafter Section alignment -

Parts List:A. Floor Section 3 - 45 1/2” x 75” - Floor Joist Frames 3 - 45 1/2” x 21” - Floor Joist Frames2 - 45 1/2” x 75” - Plywood Floor - Large2 -

47. When Rafter Section is aligned correctly, tack Rafter Section temporarily down from MiddleGable Wall framing into Rafter with 2 - 2” screws.Gable

51. With both Rafter Ridge Boards connected, completely secure Rafters to Gable framing of bothrear and middle Gable Walls. Use 8 - 2” screws per gabl

52. Attach Rafters in porch area into Top Plateof porch with 1 - 2 1/2” screw per Rafter. Onceagain, measure 91” from inside of wall plate towall plat

Roof Plywood flushwith rafter end.58. From the outside, screw down through bottom row of shingles into rafter with 1 - 2 1/2” screw.Locate Middle Roof

59. Align Middle Roof Panel as per Step 58 and screw panel down to rafters with 2 - 2 1/2” screwsin the bottom row of shingles. Lift up 2nd Outside Ro

Exposure Line64. Roof Filler Shingles are includedto cover roof seams. Starting at the bottom, slide the first Long Filler Shinglein until flush with

66. Slide in another Filler Shingle andattach as per Step 65. On your lastrow of shingles, the filler shingle isprecut to fit properly. Attach to roo

E. Miscellaneous SectionCedar RidgeRoof Caps Side Facia (4)HorizontalTrim aboveDoor (2)Bottom Skirting Sides & Rear (8)Narrow Trims (6)FlowerBox (

72. Attach Filler Trims(2 - 1/2” x 2 1/2” x 75”) torear walls. Hammer with 8 - 1 1/2” finishing nails.Trims are positioned flushwith siding and botto

74. Attach six Narrow Trims (6 - 1/2” x 2 1/2” x 79” long) to both sides of the shed. Use 8 - 1 1/2”finishing nails per piece. 75. Attach Rear Wall S

8x12 SANTA ROSA HARDWARE SHEET2 1/2”Note: screws and nails shown actual size.2”1 1/4”3/4”2” 3/4”1 1/2” 1 1/4”Tee Hinge x4Pull HandleRidge Board Conne

76. Position Back Facia (angle cut on ends) and Side Facia (square cut ends) in corner. Line Faciaup so square cut Facia is positioned between angled

81. Attaching the Gable Gusset is next. Screw 4 90 degreeSimpson Strong Ties up into plywood of roof panel with 2 -1 1/4”screws (see picture). Plac

Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected] 3282. Attach Gable Facia to exposed plywood of gable

86. Attach Door Handle, Exterior Barrel Bolt and Interior Barrel Bolt to door. Handle is positionedon top door, Barrel Bolt on bottom door and Interio

Congratulations on building your8x12 Santa Rosa Garden Shed!Note: Our Sheds are shipped as unfinished products. If exposed to the elements, the west

FlushwithframingPlywood FloorLarge (2)Floor JoistFramesLarge (3)Floor Runners (10)Plywood FloorSmall (2)Exploded view of all parts necessary to comple

7.Attach Floor Runners to completed floor frame.There are 2 floor runners per 136 1/2” side and 5completed runners in total. Use 6 - 2 1/2” screwsper

10. Position Plywood Floor pieces (4) on top of completedfloor joists. Plywood will sit slightly back from outside edge ofFloor Joist Framing. Hint:

Exploded view of all parts necessary to complete theWall Section. Identify all parts prior to starting.13. Lay out all the wall panels and become fam

16. Starting at Rear Corner, position a Wall Panel on top of plywood floor. Depending on your preference, you may use a solid or window wall panel in

17. Position rear corner wall into place and attach together with3 - 2 1/2” screws. Screw at the top, middle and bottom of 2x3stud.Start positioning